English Site

100 - 240VAC Input Voltage Range
≤0.13A No Load Input Current at 230VAC
≤0.5A Full Load Input Current at 230VAC
50 - 60Hz~ AC Input Frequency
≥78% Efficiency
≥0.9 Power Factor
Constant Voltage and Current Range Selection:
0 - 16.4V 0 - 5.1A 0 - 16V / 5A selection I
0 - 27.6V 0 - 3.1A 0 - 27V / 3A selection II
0 - 36.8V 0 - 2.3A 0 - 36V / 2.2A selection III
Constant Voltage Characteristics:
≤30mV Load Regulation (0 - 100%)
≤4mV Line Regulation (±10%)
≤30mV Ripple & Noise (peak-peak)
Constant Current Characteristics:
≤10mA Load Regulation (0 - 100%)
≤10mA Line Regulation (±10%)
±0.5% +5counts Voltmeter & Ammeter Accuracy
Yes User adjustable upper current & voltage limits
3 Number of preset recalls of frequent use V&I setting
Yes Remote Sensing
Ramp Step Irregular Waveform Functions
3 (A, B, C) Number Voltage Level Setting
6 (AB, BA, AC, CA, BC, CB) Available Number of Combinations of Voltage Generators
0 to 600 seconds Settable Output Time Period of each Voltage Generators 
0 to 20 seconds Settable Time Period One Voltage Generator to Another
Output ON/OFF, Voltage & Current Control, Selection of Voltage and Current Range, Programmable of cyclic output and data logging of output Remote Programmable / Control by PC
Adjustable over voltage protection, Current limiting protection,
Short circuit, Overload, Over temperature
Protection
USB 1.1 Standard Communication Port
Ethernet Control Broad (ZNE-100PT) Factory Pre-installed or User Installable Optional Interface Accessory
USB Driver, Command Sets, Ethernet Setting Software, Labview® Driver for Ethernet Provided Software
CE EMC: EN 55011 LVD: EN 61010 Approvals
Natural Convection Cooling Method
53.5x127x330 mm 2x5x13 inch Dimensions (WxHxD)
Approx. 1.9 kgs 4.2 lbs Weight


This DC power supply is capable of generating Ramp and other forms of DC waveform .An ARM construction RISC 32bit micro-processor is used for such DC waveforms. There are 3 voltage generators which can either be panel controlled or by remote programming via USB port.

Through the various combinations of the settings in the time gradient and period of the generated voltages, various repeatable ramp up/down, step , triangle, and other designed wave forms of output voltage can be obtained from setting of V, I & T. In the remote programming mode various repetitive cycles with different cycle period, voltage and current can be set in the connected PC and data logging as well. With the addition of optional Ethernet control card, the power supply is capable of LAN or WAN connection such that it can be communicated ,controlled, monitored, and data logging via the internet. One PC can take care of 250 power supplies even with C type of Ethernet.

This power supply is ideal for R&D laboratory, education, burn in test especially for devices where the effect of irregular DC wave forms or surge is critical. We do provide a plication software, USB driver, command sets, Ethernet software, and Labview driver.

 

להזמנה
לקוח יקר, אנא אשר כי קראת והינך מבין ומאשר כי ידוע לי שתנאי תשלום העסקה הינם מסירת צ'ק במועד קבלת הסחורה, תוך 15 ימי עסקים וכי קראת את תנאי המכירה של חברת הוריזון אלקטרוניקה
לקבלת מידע נוסף